www.partsplaceinc.com
(248) 373 2300
tools
119
BEARING INSTALLATION TOOLS
Repair shops charge
$200 to replace a bear-
ing. You can do it for
$44.00 and two hours.
All you need is the
tool and a new bear-
ing. No alignment is
necessary. Bearings are
pre-greased.
WE RENT THIS TOOL FOR "DO-IT-YOURSELF
"BEARING INSTALLATION WITHOUT EVEN
TAKING THE SPINDLE OFF THE CAR. Deposit for
the rental tool is $180. We subtract the rental charge
from the deposit. The rental charge covers use of the
tool for two weeks. We charge extra for overdue tools.
Rental charge is $20. (You can also use a conventional
arbor press or have a machine shop do it for you, but
you will have to remove the spindle if you use an arbor
press.)
ALL VW & AUDI `75-98
#SN5300
Tool Deposit. . . . . . . . . . . . . . . . . . .
$
CALL
WE SELL THE TOOLS ALSO
#SN19482
Tool Purchase . . . . . . . . . . . . . . . . .
$
399.
95
#SN39630
Tool Rental. . . . . . . . . . . . . . . .
$
60.
00
This tool enables you to easily install or
remove the C-shaped spring clamps used on
81 and up VWs. It's fingers go into the two
holes and as you turn the tool's nut, it pulls
the clamp open for easy installation.
#SN03515. . . . . . . . . . . . . . . . . . . .
$
39.
95
Also available as a
rental for $16.00
EXHAUST SPRING
CLIP TOOL
Specialty Tools
Alignment gauge being used to align
shift lever and selector lever.
Golf/Jetta all`85-92 and all Golf/Jetta 2.0L, 4 cylinder,
`93-99.5. This shifter tool is required to line the shift-
ing mechanism to prevent grinding of gears. It works
only for this application, but is required to get proper
alignment. This tool will save you days of adjusting
and readjusting.
-I tried it before I bought the tool--
it was impossible.
#SN14520
. . . . . . . . . . . . . . . . . . . . . . . . . .
$
19.
95
SHIFTER
ALIGNMENT TOOL
Golf/Jetta
`85-99.5
STRUT INSTALLATION
TOOLS
F
G
D
E
F
G
B
D
E
VW RABBIT - SCIROCCO - GOLF - JETTA
Transmission Tools
A
C
[A]
All Rabbits, Sciroccos, Jettas, and Golfs
have a
"backwards" clutch set-up. The clutch is bolted to the
engine and the flywheel is bolted to the clutch. This is
backward to what you might expect. It's impossible to
align with the old "broom stick" method. Made of 30%
glass filled nylon for strength to last a lifetime. Easy to use.
Impossible without it. Price reduced, Save
$
4.
00
!
G/J/S 16v `86-92, G/J 2.0 `93-99.5
#SN19684
. . . . . . . . . . . . . . . . . . . . . . . . . .
$
7.
95
#SN3500
. . . . . . . . . . . . . . . . . . . . . . . . . . .
$
7.
95
[B]
The VW Fox type car with inline engine . .
used the Beetle style clutch alignment tool.
#SN3519
. . . . . . . . . . . . . . . . . . . . . . . . . . .
$
5.
95
[C]
When removing the C.V. Joint Bolts,
. . . . .
clean them out with a straightened paper
. .
clip, then put the tool in the bolt and give it
a few good . . . .raps with a hammer to loosen it.
Allen Star C.V. Joint Tool 8mm, 12-point allen
#SN3481
. . . . . . . . . . . . . . . . . . . . . . . . .
$
8.
95
[D]
If you have already damaged your bolts, . .
we sell them in lots of 6 new ones
CV Joint bolts.
#SN12355 . . . . . . . . . . . . . . . . . . . . . . . . . .
$
9.
95
[E]
Socket for transmission 17mm Drain
. . . . . . . . .
Plug all VW #SN13677 . . . . . . . . . . . . . . . . . . . . . . . .
$
8.
95
[F]
30 mm Socket for big axle nut
#SN3478
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
$
7.
95
30 mm Axle Nut
VW says replace this everytime!
#SN1971
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
$
3.
95
[G]
9 mm 12 pt Socket for removing
. . . . . . . . . . .
clutch bolts all Water cooled
#SN14546
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
$
5.
95
Clutch Alignment Tool
This unique tool has been designed to allow for the easy
removal and installation of the top shock retaining nut
used on most from wheel drive Volkswagens and Audis.
Removal of this nut is difficult as it is round on the outside
and only has a slot across the top for gripping. The shock
shaft also can rotate and must be held from turning when
the nut is removed or installed. This speciality tool has a
slot drive to fit the slot in the top of the retaining nut, a
hole through its center to allow for an allen wrench to hold
the shock from turning, and a 22mm/7/8 inch hex diameter
for easy wrench usage. Made from heat treated steel, this
tool comes in a black finish.
#SN3503. . .
$
19.
95
VW STRUT SHOCK NUT
SOCKET
for Golf / Jetta
`85-92
This tool is necessary for dis-
assembling & reassembling a
strut assembly (after it's off the
car) to change springs, inserts
or bearings.
#S
or bearings.
STRUT MOUNT TOOL
This tool removes the nut needed to take the strut off
your car. It's not absolutely necessary but it makes the
job easier. You can manage with a socket, vise grip and
allen wrench but it's hard.
#SN13782
German . . . . . . . . . . . . . . . . . . . . . . . .
$
39.
95
#SN14470
Non German . . . . . . . . . . . . . . . . . . . . .
$
29.
95
ALL RABBIT, JETTA,
GOLF, SCIROCCO
We sell a spring com-
pressor tool; it's not
U.S. made, but it
works and will last for
100 spring jobs. It's
plenty strong enough
for VW springs, a little
weak for Ford Truck
springs. It's low price
can fool you. Follow
the directions.
SPRING COMPRESSOR KIT
#SN3530 . . .
$
24.
95
-
t
t
r
s
h
e
k
e
w
$
24
95